INT. SITES: 32MB Blank Janome CF Card (has a nice Label and a protective

32MB blank JANOME CF Card for CF Type I & II

it's a truly genuine product that you can trust 

Just a Fast and Perfect Capacity for your Embroidery Design Set or your Special Collection.

This genuine heavy duty CF Card is compatible and will work with the following particular "model numbers" of Janome; Kenmore Elite; Bernina Deco & Elna's machines:  

Janome MC 200E; MC 300; MC 300E; MC 350E; MC 9500; MC 9700; MC 9900; MC 10000; MC 10001; MC 11000; MC 11000SE; MC12000; MC 15000; MB4; MB4N and the kenmore Elite 19005 and Bernina Deco 300, 330 and 400 as some of Elna's embroidery machines such as: EL 8200; EL 8300; EL 820; EL 8600; EL 9500 and EL 9600.

Please note: some of the above listed models numbers (specially latest model ones) has a USB built-in port into the machine so if that is the case than no need to use a Cf Card or an ATA Card Adapter or a Card Reader option, however those models which might also happen have that USB port, are listed in here in case the USB port is damaged, faulty and does not work anymore (and is far too expensive or hard to repair.. ) so in that case you could use this option (which is the use of that adapter slot specially on the side of your machine for the ATA Card Adapter) in this case my CF Card/s will work for you but I sell all those 3 units separately OR I also sell them all as in one complete special Special Package as adv. and shown in my E-bay store, which works out a lot cheaper if you buy this whole complete Janome Special Package.

My new CF card is a 32 MB capacity and is just ideal and super perfect capacity for your Janome embroidery machine and it's even better then any higher memory capacity because you should not put more then 30 to 40 designs in each card as the more then 40 designs you add onto your Cf card  the much slower your machine will be as it will take much more time to read and it can often even freeze or give you error messages too. often clients asks me: how many designs can I put in a CF card.. well each design or pattern can be anything from an average of 10 k in capacity and up to roughly 70 K (if it is a large design) so each 32MB CF card can take up to 3200 K capacity (32MB = 3200K) which means one can put in each card anything between 50 and up to 320 designs depending how big the designs are.. but roughly as an average figure it's about 200 designs each card can take BUT again, in reality you should not put more then 30 to maximum 40 designs in each CF card as all embroidery machines has a very small little  brain (memory capacity) and are not like computer memory..  

that's why you do not really need a bigger capacity cards at all, like a 64MB or 120MB or even a 1GB etc.. as they are useless and a waste of your time and money since in reality and in practice you should only put a maximum of 30 - 40 designs in it. also you always can delete designs from the CF Card and add new ones instead (using the card reader/writer which I sell on this site) but that is not a good idea so avoid deleting over and over again so many times as eventually the card might lose capacity and also becomes unstable to use.. 

 Each CF Card also comes with a nice special & secure protective case& a special label too on the card itself to enable you to write headings, descriptive details etc.. there are 5 lines I made for you so plenty of room to write on that label what's inside your cf card.

Also for all those Janome machine model numbers mentioned above, you must have a special ATA PCMCIA CARD "ADAPTER" Compatible with Type II (and not CF type I) because you'll need to put your CF design CARD into this CF adapter II FIRST and then insert the adapter (which have the CF card inside it) into the slot in your Janome machine, then press the embroidery icon on your machine screen and when it opens, just choose a card option. That’s all! So if you do not have this special CF card ATA PCMCIA "Adapter Type II" than you can buy if you wish from my E-bay srore, it is truly heavy duty, genuine and at a low price too!

most compatible particular Janome machines model numbers that I've listed above have a slot on the side of the machine to insert a Card Adapter in it so you can put your Cf Card (which has the designs or patterns that you copied from your computer) into that Adapter and than insert the Adapter (with the card inside it) into that slot on your machine and your Janome machine should be ready to stitch your patterns, is that simple really. 

Returns are accepted if item is returned in same new condition it was received in so full refund will be given but minus shipping cost (as all shipping cost and both ways are on the buyer).